View MC74ACT541MEL_629766.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC74AC540, MC74ACT540, MC74AC541, MC74ACT541 Octal Buffer/Line Driver with 3-State Outputs
The MC74AC540/74ACT540 and MC74AC541/74ACT541 are octal buffer/line drivers designed to be employed as memory and address drivers, clock drivers and bus oriented transmitter/receivers. The MC74AC541/74ACT541 is a noninverting option of the MC74AC540/74ACT540. These devices are similar in function to the MC74AC240/74ACT240 and MC74AC244/74ACT244 while providing flow-through architecture (inputs on opposite side from outputs). This pinout arrangement makes these devices especially useful as output ports for microprocessors, allowing ease of layout and greater PC board density.
Features http://onsemi.com
PDIP-20 N SUFFIX CASE 738 1
* 3-State Outputs * Inputs and Outputs Opposite Side of Package, Allowing Easier * * * * *
Interface to Microprocessors Outputs Source/Sink 24 mA MC74AC540/74ACT540 Provides Inverted Outputs MC74AC541/74ACT541 Provides Noninverted Outputs ACT540 and ACT541 Have TTL Compatible Inputs Pb-Free Packages are Available
SOIC-20W DW SUFFIX CASE 751D 1
TSSOP-20 DT SUFFIX CASE 948E 1
SOEIAJ-20 M SUFFIX CASE 967
TRUTH TABLE
Inputs OE1 L H X L OE2 L X H L D H X X L Outputs 540 L Z Z H 541 H Z Z L
1
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking section on page 9 of this data sheet.
H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance
(c) Semiconductor Components Industries, LLC, 2006
1
December, 2006 - Rev. 8
Publication Order Number: MC74AC540/D
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
OE1 VCC OE2 OE1 VCC OE2
1 2 3 4 5 6 7 8 9
20 19 18 17 16 15 14 13 12 11
1 2 3 4 5 6 7 8 9
20 19 18 17 16 15 14 13 12 11
GND
10
GND
10
Figure 1. MC74AC540/74ACT540
Figure 2. MC74AC541/74ACT541
MAXIMUM RATINGS
Symbol VCC VIN VOUT IIN IOUT ICC Tstg Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin DC Output Sink/Source Current, per Pin DC VCC or GND Current per Output Pin Storage Temperature Value -0.5 to +7.0 -0.5 to VCC +0.5 -0.5 to VCC +0.5 20 50 50 -65 to +150 Unit V V V mA mA mA C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VIN, VOUT Supply Voltage DC Input Voltage, Output Voltage (Ref. to GND) VCC @ 3.0 V tr, tf Input Rise and Fall Time (Note 1) AC Devices except Schmitt Inputs Input Rise and Fall Time (Note 2) ACT Devices except Schmitt Inputs Junction Temperature (PDIP) Operating Ambient Temperature Range Output Current - High Output Current - Low VCC @ 4.5 V VCC @ 5.5 V tr, tf TJ TA IOH IOL VCC @ 4.5 V VCC @ 5.5 V Parameter AC ACT Min 2.0 4.5 0 - - - - - - -40 - - Typ 5.0 5.0 - 150 40 25 10 8.0 - 25 - - Max 6.0 5.5 VCC - - - - - 140 85 -24 24 ns/V C C mA mA ns/V V V Unit
1. VIN from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. VIN from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times.
http://onsemi.com
2
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
DC CHARACTERISTICS
74AC VCC (V) 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 VOL Maximum Low Level Output Voltage 3.0 4.5 5.5 3.0 4.5 5.5 IIN IOZ Maximum Input Leakage Current Maximum 3-State Current Minimum Dynamic Output Current Maximum Quiescent Supply Current 5.5 TA = +25C Typ 1.5 2.25 2.75 1.5 2.25 2.75 2.99 4.49 5.49 - - - 0.002 0.001 0.001 - - - - 74AC TA = -40C to +85C Guaranteed Limits 2.1 3.15 3.85 0.9 1.35 1.65 2.9 4.4 5.4 2.56 3.86 4.86 0.1 0.1 0.1 0.36 0.36 0.36 0.1 2.1 3.15 3.85 0.9 1.35 1.65 2.9 4.4 5.4 2.46 3.76 4.76 0.1 0.1 0.1 0.44 0.44 0.44 1.0 Unit V Conditions VOUT = 0.1 V or VCC - 0.1 V VOUT = 0.1 V or VCC - 0.1 V IOUT = -50 mA V *VIN = VIL or VIH -12 mA IOH -24 mA -24 mA IOUT = 50 mA V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA VI = VCC, GND VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND VOLD = 1.65 V Max VOHD = 3.85 V Min VIN = VCC or GND
Symbol VIH
Parameter Minimum High Level Input Voltage Maximum Low Level Input Voltage Minimum High Level Output Voltage
VIL
V
VOH
V
V
mA
5.5
-
0.5 - - 8.0
5.0 75 -75 80
mA mA mA mA
IOLD IOHD ICC
5.5 5.5 5.5
- - -
*All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC.
http://onsemi.com
3
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
AC CHARACTERISTICS (For Figures and Waveforms - See AND8277/D at www.onsemi.com)
74AC TA = +25C CL = 50 pF Min 1.5 1.5 1.5 1.5 3.0 2.0 2.5 2.0 2.5 1.5 2.0 1.5 2.0 1.5 2.0 1.5 3.0 2.0 2.5 1.5 3.5 2.0 2.5 2.0 Typ 5.5 4.0 5.0 4.0 8.5 6.5 7.5 6.0 8.5 7.5 7.0 6.0 5.5 4.0 5.5 4.0 8.0 6.0 7.0 5.5 9.0 7.0 6.5 5.5 Max 7.5 6.0 7.0 5.5 11 8.5 10 7.5 13 10.5 10 8.0 8.0 6.0 8.0 6.0 11.5 8.5 10 7.5 12.5 9.5 9.5 7.5 74AC TA = -40C to +85C CL = 50 pF Min 1.0 1.0 1.0 1.0 2.5 2.0 2.0 1.5 1.5 1.0 2.0 1.5 1.5 1.0 1.5 1.0 3.0 1.5 2.5 1.0 2.5 1.0 2.0 1.0 Max 8.0 6.5 7.5 6.0 12 9.5 11 8.5 14 11 11 9.0 9.0 6.5 8.5 6.5 12.5 9.5 11.5 8.5 14 10.5 10.5 8.5 Unit ns ns ns ns ns ns ns ns ns ns ns ns
Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tPLH tPHL tPZH tPZL tPHZ tPLZ
Parameter Propagation Delay Data to Output (AC540) Propagation Delay Data to Output (AC540) Output Enable Time (AC540) Output Enable Time (AC540) Output Disable Time (AC540) Output Disable Time (AC540) Propagation Delay Data to Output (AC541) Propagation Delay Data to Output (AC541) Output Enable Time (AC541) Output Enable Time (AC541) Output Disable Time (AC541) Output Disable Time (AC541)
VCC* (V) 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0
Fig. No. 3-5 3-5 3-7 3-8 3-7 3-8 3-5 3-5 3-7 3-8 3-7 3-8
*Voltage Range 3.3 V is 3.3 V 0.3 V. Voltage Range 5.0 V is 5.0 V 0.5 V.
http://onsemi.com
4
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
DC CHARACTERISTICS
74ACT VCC (V) 4.5 5.5 4.5 5.5 4.5 5.5 4.5 5.5 VOL Maximum Low Level Output Voltage 4.5 5.5 4.5 5.5 IIN DICCT IOZ Maximum Input Leakage Current Additional Max. ICC/Input Maximum 3-State Current Minimum Dynamic Output Current Maximum Quiescent Supply Current 5.5 5.5 TA = +25C Typ 1.5 1.5 1.5 1.5 4.49 5.49 - - 0.001 0.001 - - - 0.6 2.0 2.0 0.8 0.8 4.4 5.4 3.86 4.86 0.1 0.1 0.36 0.36 0.1 - 0.5 - - 8.0 74ACT TA = -40C to +85C Guaranteed Limits 2.0 2.0 0.8 0.8 4.4 5.4 3.76 4.76 0.1 0.1 0.44 0.44 1.0 1.5 5.0 75 -75 80 Unit V V V Conditions VOUT = 0.1 V or VCC - 0.1 V VOUT = 0.1 V or VCC - 0.1 V IOUT = -50 mA *VIN = VIL or VIH IOH -24 mA -24 mA IOUT = 50 mA *VIN = VIL or VIH 24 mA IOL 24 mA VI = VCC, GND VI = VCC - 2.1 V VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND VOLD = 1.65 V Max VOHD = 3.85 V Min VIN = VCC or GND
Symbol VIH VIL VOH
Parameter Minimum High Level Input Voltage Maximum Low Level Input Voltage Minimum High Level Output Voltage
V
V
V
mA mA mA mA mA mA
5.5
-
IOLD IOHD ICC
5.5 5.5 5.5
- - -
*All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time.
http://onsemi.com
5
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
AC CHARACTERISTICS (For Figures and Waveforms - See AND8277/D at www.onsemi.com)
74ACT Symbol Parameter VCC* (V) Min tPLH tPHL tPZH tPZL tPHZ tPLZ tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay Data to Output (ACT540) Propagation Delay Data to Output (ACT540) Output Enable Time (ACT540) Output Enable Time (ACT540) Output Disable Time (ACT540) Output Disable Time (ACT540) Propagation Delay Data to Output (ACT541) Propagation Delay Data to Output (ACT541) Output Enable Time (ACT541) Output Enable Time (ACT541) Output Disable Time (ACT541) Output Disable Time (ACT541) 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 1.0 1.0 1.0 1.0 1.0 1.5 1.5 1.5 2.0 1.5 2.0 2.0 TA = +25C CL = 50 pF Typ - - - - - - - - - - - - Max 7.0 8.0 10.5 9.5 12.0 9.0 7.5 7.5 10.0 9.5 11.0 9.0 74ACT TA = -40C to +85C CL = 50 pF Min 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Max 7.5 8.5 11.5 10.5 12.5 10 8.0 8.0 11.0 10.5 12.0 10 ns ns ns ns ns ns ns ns ns ns ns ns 3-5 3-5 3-7 3-8 3-7 3-8 3-5 3-5 3-7 3-8 3-7 3-8 Unit Fig. No.
*Voltage Range 5.0 V is 5.0 V 0.5 V.
CAPACITANCE
Symbol CIN CPD Input Capacitance Power Dissipation Capacitance Parameter Value Typ 4.5 30 Unit pF pF Test Conditions VCC = 5.0 V VCC = 5.0 V
http://onsemi.com
6
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
ORDERING INFORMATION
Device MC74AC540N MC74AC540NG MC74ACT540N MC74ACT540NG MC74AC540DW MC74AC540DWG MC74AC540DWR2 MC74AC540DWR2G MC74ACT540DW MC74ACT540DWG MC74ACT540DWR2 MC74ACT540DWR2G MC74ACT540DTR2 MC74ACT540DTR2G MC74ACT540MEL MC74ACT540MELG MC74AC541N MC74AC541NG MC74ACT541N MC74ACT541NG MC74AC541DW MC74AC541DWG MC74AC541DWR2 MC74AC541DWR2G MC74ACT541DW MC74ACT541DWG MC74ACT541DWR2 MC74ACT541DWR2G Package PDIP-20 PDIP-20 (Pb-Free) PDIP-20 PDIP-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) TSSOP-20* TSSOP-20* SOEIAJ-20 SOEIAJ-20 (Pb-Free) PDIP-20 PDIP-20 (Pb-Free) PDIP-20 PDIP-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) SOIC-20 SOIC-20 (Pb-Free) 1000 / Tape & Reel 38 Units / Rail 1000 / Tape & Reel 38 Units / Rail 18 Units / Rail 2000 / Tape & Reel 2500 / Tape & Reel 1000 / Tape & Reel 38 Units / Rail 1000 / Tape & Reel 38 Units / Rail 18 Units / Rail Shipping
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *These packages are inherently Pb-Free.
http://onsemi.com
7
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
ORDERING INFORMATION (continued)
Device MC74AC541DTR2 MC74AC541DTR2G MC74ACT541DT MC74ACT541DTG MC74ACT541DTR2 MC74ACT541DTR2G MC74AC541M MC74AC541MG MC74AC541MEL MC74AC541MELG MC74ACT541M MC74ACT541MG MC74ACT541MEL MC74ACT541MELG Package TSSOP-20* TSSOP-20* TSSOP-20* TSSOP-20* TSSOP-20* TSSOP-20* SOEIAJ-20 SOEIAJ-20 (Pb-Free) SOEIAJ-20 SOEIAJ-20 (Pb-Free) SOEIAJ-20 SOEIAJ-20 (Pb-Free) SOEIAJ-20 SOEIAJ-20 (Pb-Free) 2000 / Tape & Reel 40 Units / Rail 2000 / Tape & Reel 40 Units / Rail 2500 / Tape & Reel 75 Units / Rail 2500 / Tape & Reel Shipping
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *These packages are inherently Pb-Free.
http://onsemi.com
8
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
MARKING DIAGRAMS
PDIP-20
SOIC-20W
TSSOP-20
SOEIAJ-20
20 20 MC74AC54xN AWLYYWWG 1 1 AC54x AWLYYWWG
20 AC 54x ALYWG G 1
20 74AC54x AWLYWWG 1
20 20 MC74ACT54xN AWLYYWWG 1 1 ACT54x AWLYYWWG
20 ACT 54x ALYWG G 1
20 74ACT54x AWLYWWG 1
x = 0 or 1 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location)
http://onsemi.com
9
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
PACKAGE DIMENSIONS
PDIP-20 N SUFFIX PLASTIC DIP PACKAGE CASE 738-03 ISSUE E
-A-
20 1 11 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
B
10
C
L
-T-
SEATING PLANE
K M E G F D
20 PL
N J 0.25 (0.010)
M 20 PL
0.25 (0.010) TA
M
M
TB
M
DIM A B C D E F G J K L M N
INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0_ 15 _ 0.020 0.040
MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01
SOIC-20W DW SUFFIX CASE 751D-05 ISSUE G
D
A
11 X 45 _
q
H
M
B
M
20
10X
0.25
E
NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L q MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_
1
10
20X
B 0.25
M
B TA
S
B
S
A
SEATING PLANE
h
18X
e
A1
T
C
http://onsemi.com
10
L
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
PACKAGE DIMENSIONS
TSSOP-20 DT SUFFIX CASE 948E-02 ISSUE C
K REF
M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. MILLIMETERS INCHES DIM MIN MAX MIN MAX A 6.40 6.60 0.252 0.260 B 4.30 4.50 0.169 0.177 C --- 1.20 --- 0.047 D 0.05 0.15 0.002 0.006 F 0.50 0.75 0.020 0.030 G 0.65 BSC 0.026 BSC -W- H 0.27 0.37 0.011 0.015 J 0.09 0.20 0.004 0.008 J1 0.09 0.16 0.004 0.006 K 0.19 0.30 0.007 0.012 K1 0.19 0.25 0.007 0.010 L 6.40 BSC 0.252 BSC M 0_ 8_ 0_ 8_
20X
2X
L/2
20
11
J J1 B
L
PIN 1 IDENT 1 10
-U- N
0.15 (0.006) T U
S
A -V-
N F DETAIL E
C D 0.100 (0.004) -T- SEATING
PLANE
G
H
DETAIL E
SOLDERING FOOTPRINT*
7.06 1
16X
0.36
16X
1.26
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
11
IIII IIII IIII
SECTION N-N 0.25 (0.010) M
0.15 (0.006) T U
S
0.10 (0.004)
TU
S
V
S
K K1
0.65 PITCH
DIMENSIONS: MILLIMETERS
MC74AC540, MC74ACT540, MC74AC541, MC74ACT541
PACKAGE DIMENSIONS
SOEIAJ-20 M SUFFIX CASE 967-01 ISSUE A
20
11
LE Q1 M_ L DETAIL P
E HE
1
10
Z D e VIEW P A
c
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --- 2.05 0.05 0.20 0.35 0.50 0.15 0.25 12.35 12.80 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --- 0.81 INCHES MIN MAX --- 0.081 0.002 0.008 0.014 0.020 0.006 0.010 0.486 0.504 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --- 0.032
b 0.13 (0.005)
M
A1 0.10 (0.004)
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
12
MC74AC540/D

▲Up To Search▲

Price & Availability of MC74ACT541MEL

	To Download MC74ACT541MEL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .